general problems of the 2007 Toyota 4Runner

The battery died unexpectedly (about 3 years old) and when we replaced it and tried to drive it, there was a loud continuous beep from the dash and no brakes. We replaced the abs fuse, which blew again immediately. We had to have it towed to the shop and it was confirmed it was the brake module. This exact issue just happened with our 2013 camry and it was replaced under a manufacturer warranty. I drive my kids in this car. We could have died.

Vehicle frame is extremely corroded to the point where replacing necessary items such as shocks/struts/steering components is not possible without irreparable damage. Factory welds at critical points of the frame structure are starting to fail and causing safety concerns. This vehicle is regularly garaged and only has 85,000 miles. This is unacceptable, there have been previous recalls and for other models that share this exact same frame and suspension.

When I am driving on a bumpy unlevel street and stepping on the brake paddle to slow down the brakes give out and then catch again, I find this to be very dangerous and might even cause an accident especially if there is another car to my front, this has happened to me quite a few times. The brake system has to be checked on a bumpy paved road, brakes will catch and release and catch and release. This happens every time I am on a bumpy paved road.

Complete and permanent damage of abs and brake module ian's results in no brakes while running the car.

"I am requesting that dot NHTSA investigate the driver's contribution to unintended acceleration (ua) and Toyota's accelerator/brake pedal designs that make it possible. I was driving my Toyota 4 runner in the neighborhood street of my community. My speed was less than 30mph and it accelerated suddenly. I applied the brake and instead of slowing down the vehicle began to gain speed. I pressed harder on the brake and it accelerated. The harder I tried to stop the car, the faster it went. I took my foot off the brake for a moment and the vehicle stopped accelerating. My foot was on the brake. It accelerated and would not stop so I pulled the car from the street to the curb covered by grass. It slowed down to some extent and then I intentionally to a turn and hit the median curb & tree to stop the car. I have continued to investigate unintended acceleration and have collected partial information. . . . Please formally investigate. ".

While driving with my entire family on I-95, the vehicle abs assembly began cycling repeatedly. When depressing the brakes while the abs was cycling, the brake pedal would grind and slippage occurred in the pedal pressure. No warning lights.

Over the past 9-12 months I have owned the 4runner, I have noticed the floormats slide up behind the brake and acceleration pedal when I am constantly switching between the two (eg. Heavy traffic, long trips, etc. ). I usually am able to pull them back down at a stoplight or stop sign; however, on Tuesday, July 29th, I was involved in an auto accident that was not only in heavy traffic, but while on a 200+ mile trip as well. I believe that the floor mat caused my car to have limited braking ability in addition to possible increased acceleration. The NHTSA's findings seem to be consistent with this. Additionally, the complaint with NHTSA id number: 10384563 states that "I pushed on the brake. . . But the car continued accelerating" and then "Toyota inspected the vehicle. . . And said they adjusted the mat" is one of many that have findings consistent with the malfunction that caused my wreck.

Machines break but when parts represent a risk of fatality, they should be more closely scrutinized. I got lucky when the brake booster assembly went out in my 2007 Toyota 4runner while it was parked and running in my garage for 5 minutes while I unloaded it. Had I not made the decision to let the car run while I unloaded it, a decision that I first questioned, it more than likely would've gone out the following morning when I pulled out of my steeply sloped driveway. A drop of about 10-15 feet is directly across from my driveway and there is nothing to stop anything from rolling down that drop besides the multitude of hardwoods there. I could've been on the interstate or traversing the hills and slopes that we deal with daily. A parking brake will only do so much. My 4runner is well-maintained. In fact, it had received it's regular maintenance only 5 days prior to the brake booster assembly's failure. There was no warning;no noise, no feeling, no weird behavior-just buzzers and warning lights after the fact. The car almost rolled through the garage door as well as the house. It took all of my might to stop it at 1-3 mph. I am grateful for what did not happen but concerned about any other unsuspecting 4runner owner and anyone around that 4runner if the same happens. I've been happy with my 4runner and felt safe in it until July 21. It is my third 4runner in a row. They are fantastic SUV's. I have a great relationship with my dealership, especially my service tech, who I feel looks out for me and my 4runner. But after researching brake booster assemblies in 4runners, I see multiple crashes and scary stories involving this part. I see it is unrelated to mileage or maintenance or vehicle age. It's happened at 2months old, 2 years old, 200k miles. The risk of fatality is too high to let this issue remain unattended to.

I come to a stop and my vehicle pulls, like somebody hit my vehicle from behind. Its constant , it happens all the time. I did take it to a dealer and they said there was nothing that could be done, they advised Toyota had not come out with a recall yet for that problem. They advised it was a common problem with the drivetrain . I really do not want this vehicle any more if it is always going to do this. . What makes me mad is that I just bought this vehicle in July. . . . . . . What can be done .

The contact owns a 2007 Toyota 4runner. The contact stated that while driving 30 mph, she noticed that her vehicle would not stop once the brakes were applied. She had to utilize the emergency brake and was able to stop the vehicle. The vehicle was not taken to the dealer for inspection or repair. The manufacturer was contacted and stated that the vehicle was no longer under warranty. The vehicle was not repaired. The failure and the current mileage was 63,000. The VIN was not available.

The whole area of exposed steel has been so corroded with rust that I acnnot even remove bolts to service several of the key components in the engine compartment. The frame, cross members, suspension etc. Are also affected in this way. I'm no expert but it is progressively becoming more and more unsafe to drive especially if I lose brakes or some other necessary function. Please help, is this a bad batch of cheap steel?.

Tl-the contact owns a 2007 Toyota 4runner. The contact stated that while driving, there was a beeping noise in the engine area and the brake pedal began vibrating. The vehicle was taken to the dealer who performed a diagnostic that located the failure at the abs brake actuator. The vehicle was not repaired. The failure and the current mileage was 28,000. Kmj.

2007 Toyota 4runner with 55,000 miles. Hydroboot assembly (abs brake system computer and motor assembly) abruptly went out on March 22 with my 18 yo driving. He could not immediately get the car to stop using all of his strength and force. Toyota dealership claims this is a "freak" occurance. If this would have been on a highway or my 15 yo with learners permit driving, this would have been a fatal accident. Toyota says "out of warranty" and "sorry".

The contact owns a 2007 Toyota 4runner. The contact was driving approximately 15 mph proceeding to make a right turn. When the brakes were engaged there was a loud screeching noise outside of the vehicle; and several warning indicators illuminated on the instrument panel. Suddenly, the engine stalled. The ignition was turned off, and then restarted. The vehicle resumed and when the brake pedal was applied there was no power response. The contact drove over a curbside and the vehicle came to a complete stop. The vehicle was towed two different independent mechanics and they informed that the failure was related to the entire brake system. The vehicle was towed to an authorized dealer for a third diagnosis and repair at the time of the complaint. The failure mileage was 80,481. The VIN was unavailable.

Information redacted pursuant to the freedom of information act (foia), 5 u. S. C. 552(b)(6) vehicle is a Toyota 2007 4runner sr5. VIN [xxx]. The plastic cover (Toyota part no. 72124 35010) that fits over the front driver seat hold down bolts broke off and slid under the brake pedal. The brakes could not be used until I removed the loss part.

The contact owns a 2007 Toyota 4 runner. He stated that when he was driving 30 mph and began slowing down with his foot on the brake pedal, the braking system failed and the vehicle did not slow down. He then depressed the brake pedal very hard multiple times to stop the vehicle. The failure has also occurred 5 times. The vehicle was then taken to the dealer who stated that there was nothing wrong and the failure could not be duplicated. No repairs were made to the vehicle. The failure mileages was 20,000. The current mileage is 25,000. Updated 6/1/10 updated 06/04/10.

The contact previously owned a 2007 Toyota 4runner. The contact stated that the braking system was defective because when she would depress the brake pedal, the vehicle would shake and keep moving forward. The contact noticed the issue at least 6 times. She took the vehicle to the dealership and after the dealer test drove the vehicle, she was informed that they could not find anything wrong with the vehicle. She called the manufacturer and a representative was sent to inspect the vehicle; however, the rep stated that they could find nothing wrong with the vehicle. The contact traded the vehicle for another. The current and failure mileages (when the contact returned the vehicle) were approximately 10,000.