Technical Service Bulletins of the 2014 Hino Cab-over
There have been 29 technical service bulletins issued for the 2014 Hino Cab-over.
1
2014 Hino Cab-over power train TSB (Bulletin 167-T2305-2)
Bulletin Date:
May. 16, 2023
Component:
Power train.
Bulletin Summary:
Subject vehicles may experience a harsh shift condition with no dtc (diagnostic trouble codes) set. If this condition is experienced, inspect the transmissions turbine speed sensor for proper operation.
Dpf shield br a cket corrosion - subject vehicles may exhibit a broken dpf shield mounting bracket ddue to corrosion perforation. An enhanced dpf shield bra cket made from stainless steel is now available to prevent this condition from recu
5
2014 Hino Cab-over vehicle speed control TSB (Bulletin SB-15-045)
Bulletin Date:
Nov. 19, 2015
Component:
Vehicle speed control.
Bulletin Summary:
Hino conventional trucks (238, 258, 268 or 338) equipped with a snow plow specification stationary grille. Fiberglass repair methods have been made available to address hood cra ck concerns. In the event a subject vehicle experiences cra ck
6
2014 Hino Cab-over fuel system TSB (Bulletin TT-14-013)
Bulletin Date:
Oct. 28, 2015
Component:
Fuel system.
Bulletin Summary:
Some customer?s may request to enable to idle shutdown to save on fuel costs and idling time. The procedure below will detail how to enable the idle shutdown timer.
When replacing an engine block with service part no. , 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 o
The following is to inform you of the above caption. This service data should be attached to the relevant pages of the workshop manuals for maintenance and to use for servicing.
The broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised procedure h
14
2014 Hino Cab-over vehicle speed control TSB (Bulletin SA-14-026)
Bulletin Date:
Nov. 4, 2014
Component:
Vehicle speed control.
Bulletin Summary:
The broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised procedure h
When diagnosing a concern with the scr system, the technician may notice crystallized def (diesel exhaust fluid) on the tip of the def injector. Crystallized def on the tip of the injector is a normal occurrence and does not indicate that t
16
2014 Hino Cab-over gasoline fuel system TSB (Bulletin TT-14-026)
Bulletin Date:
Oct. 31, 2014
Component:
Gasoline fuel system.
Bulletin Summary:
When diagnosing a concern with the scr system, the technician may notice crystallized def (diesel exhaust fluid) on the tip of the def injector. Crystallized def on the tip of the injector is a normal occurrence and does not indicate that t
During diagnosis of the exhaust aftertreatment system, the technician may find that the combustion chamber igniter plugs are covered in soot or appear to be excessively worn. If the igniters are dirty or have some wear, this alone does not
The following procedure is for resetting the engine hour meter display showing total running time, driving time, and idling time of the vehicle in minutes and seconds. Total shows the time from engine start to engine stop. Drive or idle sho
19
2014 Hino Cab-over vehicle speed control TSB (Bulletin SB-14-020)
Bulletin Date:
Sep. 22, 2014
Component:
Vehicle speed control.
Bulletin Summary:
When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
20
2014 Hino Cab-over lane departure TSB (Bulletin SB-14-016)
Bulletin Date:
Sep. 8, 2014
Component:
Lane departure.
Bulletin Summary:
In the event that one of the subject vehicles is driven while the abs warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an abs warning lamp illuminated can lead to overheating