Table 1 shows one common wheel related problems of the 2008 Chrysler Town & Country.
| Problem Category | Number of Problems |
|---|---|
| Wheel problems |
My tire light came on I check the air pressure and found one of the valve stems broke off. Took it into tire shop and was told Chrysler is having a problem with the stems. Had to replace one. Need new tires and will have to replace the other three.
Vehicle has 4 different sizes of tires. Dark out when I bought vehicle. Also transmission slips in and out of gear. A/c immediately quit working. Oily burning smell after driven. Uses an abundant amount of gas $25-30 a day. My friend noticed the cord coming out of the tire a couple weeks after I got the van because it was making klunking sounds. I took it to goodyear and they were appalled!.
While I'm driving my vehicle home from work it will stall, taking the ability to steer away. Like it just shuts off right in the middle of driving. It usually happens when I am turning or going around a curve.
Tl-the contact owns a 2008 Chrysler town and country. The contact noticed that there was not a valve cover cap on the front driver side tire. In addition, the valve stem fractured from the tire causing the air remove from the tire rapidly. The contact mention had to put on a spare tire. The vehicle was taken to a dealer where it was diagnosed that the valve assembly needed to be replaced. The vehicle was repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 80,000. Ak.
Tire pressure monitoring system (tpms)- routinely shows I have 4 flat tires. Ignition switch, tpms sensors, wiring, starter have all been replaced, some numerous times. In addition- car will sometimes not start. We have been dealing with this since June 2015. The vehicle has been to the dealer for this at least 10 times, no resolution.
Chrysler declined covering my car under k19 recall because it was manufactured 2 days before the recall date and also they also said my car was sold originally in ok. The car resides in IL since 2013. Even my service advisor thought it was covered by the same recall. The recall cover both of the front wheel bearings, the left one was replaced almost a year ago on my expenses in Chrysler dealer and now after 10 k miles the right wheel bearing started to create humming and grinding sound. I contacted Chrysler customer service and they said that they can't do anything for me because my car was manufactured 2 days before the k19 time frame. I don't mind paying for repairing my car, but this minivan traveled to the dealership 19 times for many different expensive repairs since August 2013, this is too much I appreciate your help in this regard.
My auto service technician was checking the tire pressure when the valve stem broke off at the valve cap area causing the left rear tire to deflate. The technician said this was due to the dis-similar metals corroding and weakening the valve stem. He said that if the valve stem where to fail at highway speeds it could be very dangerous. This vehicle has the tire pressure displayed on the dashboard.
Just purchased a used 2008 Chrysler Town & Country. It was taken to the shop for extensive maintenance, including the replacement of the hub bearing - front right with oem parts. Upon further inspection we ascertained that there is a recall for this part for the 2008 model year. Chrysler notification k19 states: "the front wheel bearings on your vehicle (VIN: xxxxxxx) may develop a growling or grinding noise. The bearing noise may increase or decrease during turning maneuvers. What your dealer will Chrysler will service your vehicle free of charge (parts and labor) well, it turns out that my vehicle VIN number is not included in the recall. Is there a reason for this? can you look into this? thank you.
The contact owns a 2008 Chrysler town and country. The contact received notification of NHTSA campaign number: 14v373000 (air bags, electrical system); however, the part needed to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. In addition, while driving at numerous speeds, the accelerator pedal was depressed and the vehicle started shaking without warning. The contact also stated that when the vehicle was parked, the key was difficult to remove from the ignition. The vehicle was not repaired. The failure mileage was unknown.
Our van makes a grinding or rubbing noise coming from the front end/axles. It is especially noticeable when we are turning. It sounds like a fluttering/grinding of metal or some part that is revolving with the wheels as we drive. We had the brake rotors replaced and pads replaced. That helped with the shimmy we felt while braking, but the rubbing/grinding sounds persist. We are being told it might be wheel bearings. Others have reported similar problem to NHTSA for this model/year t&c Mini van. There is a service notification k19 for this exact problem on some 2008 models. I think our van VIN# should be added to that list of "some 2008 models. ".
The rear wheel bearings need replaced. There is a loud growling or rubbing sound in the back. The dealership is saying that there is no recall.
The contact owns a 2008 Chrysler Town & Country. The contact stated that when he touched the rear driver side tire pressure monitoring system valve stem, it disintegrated due to corrosion and caused the tire to become deflated. The vehicle was taken to a dealer where it was diagnosed that the tire pressure sensor needed to be replaced. The manufacturer was notified of the failure. The vehicle was repaired. The approximate failure and current mileage was 98,000.
I was putting air in rear passenger side tire, when valve broke in half. Stem was corroded upon inspection. I also noticed that another stem had been replaced already (I bought the car used) and there was still two original stems that were also corroded and probably needed replacement ASAP. Mechanic said it was pretty common with town and country vans.
Went to add air to a tire, the tpms valve stem snapped off, tire lost all air very quickly. The tpms valve stems are all corroded and all are about to fail. If one fails while driving, a very serious accident could result. Decided to purchase a different style of tpms (schrader with a rubber stem, instead of the dangerous originals with their corroding pot metal stems) for all 4 wheels at considerable expense to ensure the safety of my family. From reading forums at e. G. Allpar, this is a common problem. Chrysler surely knows about these dangerous tpms's and should be proactive and at least warn users to check for corrosion, and preferably fix their problem.
All valve stems became corroded and required replacement due to leaking and causing flat tires.
All 4 wheel stems corroded. 2 failed.
The valve stem broke off after we went to the dealership to have the tires tests. Tpms was set off by the first stem replacement we had two months earlier. We now have two replacement valves on our Town & Country. I don't even know if the replacement are from the same faulty supplier in china. But the stem are made of the same metal rather than brass. Please get a recall of these items. The manufacturer will do nothing until someone gets hurt and it does me no good to replace them if they continue to use the same faulty parts.
This is the second occurrence. Tire was low - front right - pulled in to put air in and when unscrewing the valve cap, the stem broke off into my hand. The left rear wheel did the same thing 3 months ago. Luckily the stem did not fall apart while driving as the tire went immediately flat. Each time the cost was over 85 plus the call to aaa to assist. I saw that others were having the same issue. With only 60000 miles on the vehicle, the tire pressure monitor should not be failing. Was told this was not covered under warranty.
Valve stem broke apart while taking cap off to put air in the tire.
The contact owns a 2008 Chrysler town and country. The contact stated that while driving, the rear driver¿s side tpms sensor fractured in two. The tire was unable to maintain tire pressure. The vehicle was driven to the dealer where the contact was informed that the failure was common but he would need to purchase a replacement. The vehicle was repaired. The manufacturer was contacted and offered no assistance. The failure and current mileages were approximately 43,000.
Valve stems on tpms systems are not made of brass as on the past they are of a pot metal and they corrode under the cap when you try to inflate the tie the snap off causing an instant flat. I f this was to occur at speed it would have catastrophic results. There needs to be a recall before someone gets hurt or killed.
The contact owns a 2008 Chrysler town and country. The contact stated that the rear passenger tire deflated and the stem disintegrated due to corrosion. The vehicle was taken to the dealer where it was diagnosed that the valve stem needed to be replaced. The manufacturer was made aware of the failure. The vehicle was not repaired and the failure recurred. The approximate failure mileage was 36,000 and the current mileage was 40,000.
The tire pressure monitor alerted me to a tire with low pressure. This was the second time in two weeks that the sensor had alerted me to a low pressure situation with this tire. I took the vehicle to my independent mechanic who discovered a leaking tire valve due to corrosion. This is the second valve on this van that I have had a problem with. Chrysler is not willing to do anything as far as warranty or defective part is concerned. Their service writer's opinion was - "well, you do live in the northeast and we do get poor weather". This is a lousy excuse for a know problem to Chrysler. This situation needs to be recalled before someone has a catastrophic valve failure at speed and is involved in a serious collision. I have since replaced the valve and tire monitor (thanks Chrysler for your great design - $100 for a tire valve).
I purchased a used 2008 Chrysler town and country touring edition with appx. 30,000 miles on it in late 2011. In may of 2012, I had an accident which only affected myself and the vehicle. While traveling approximately 45 mph the passenger rear wheel came off of the vehicle, causing the van to slam to the ground and me to perform emergency maneuvers to stop. The wheel, having had all five lug bolts sheared off, had bounced off of the vehicle doing considerable body damage. The brakes, axle, tire, et al had to be replaced. I chalked this up to coincidence, paid my deductible, and had over $3,000 worth of work done to repair the damage from the accident. This past Sunday, August 24th, 2014, the exact same thing happened. I was traveling slower this time, about 25 mph, and when I heard the same wheel making noise I pulled off the road into a strip mall parking lot just in time to have the wheel come off again, this time doing damage to the rear quarter panel, the bumper, the axle, brakes, tire, et cetera. It also forced me to make another emergency stop, this time in the lot, where the right side of my vehicle was damaged by the handle of a commercial dumpster that stopped my skid. I reached out to Chrysler because I cannot believe that the exact same thing to the exact same wheel would happen twice, and I now chalk it up to a parts failure on Chrysler's end. I was at first told that they were not responsible and that nothing would be done on their end. The following day, I spoke with the Chrysler dealership where the van was towed and was told by their head mechanic that the failure was due to the (factory) alloy rim. I again contacted Chrysler with this new information and was told that my case was being moved up to a "specialist" and that I would have to wait 3-5 days before I heard from them. I no longer feel safe transporting my family in this vehicle.
The valve stem became corroded and broke off under the cap. The tire lost pressure while driving due to the defective valve stem, and valve stem had to be replaced to refill the tire with air.
While starting to fill the front passenger tire with air, the valve stem portion of the tire monitoring system broke at a point where the tire deflated. Luckily we were parked. The valve stem appears corroded. All Chrysler vehicles with this type of valve stem should be recalled and a replacement (more durable) valve stem installed before the stem breaks off while driving resulting in a severe accident.
One tpms valve stem broke when I tried to add some air. Tire got flat instantly.
I found the right-rear valve stem broken, while trying to add air. It appeared to have been weakened by corrosion. The surrounding area of the wheel showed no signs of corrosion. The valve stems on this vehicle are also the tire pressure monitoring sensor (tpms) sensors. Upon inspection, I found the other valve stems/sensors in poor condition. After the spare tire was installed, the vehicle was taken to the dealer for repair, under warranty. I asked that they replace the other three sensors, since failure appears imminent. The service writer explained that, while this is a common failure, they cannot replace the part, until it is actually leaking air; because the sensors are expensive. I feel this is significant, potential safety issue, because when the stem/sensors break, there is an almost immediate, total loss of pressure in the affected tire. If the stem/sensor broke while driving, loss of vehicle control could occur. There appears to be quite a bit of discussion related to this problem on Chrysler-related internet blogs and forums. Also, it appears Chrysler knows there is a problem, since newer vehicles have stems/sensors constructed of a more robust material.
I own a 2008 Chrysler Town & Country Mini van and yesterday when I was driving on the highway, I heard a weird sound from the outside and could smell something burning. I pulled over and checked around to see smoke coming out from my left rear wheel. I put some water on it and had to tow it to the dealer as I did not want to take any chance. The dealer (gurnee Dodge) told me that I have to replace my rear brake pads and the rotors as they are worn out and at only 21,000 miles. I have never had to replace brake pads and rotors at such a low mileage on any vehicle I have owned. I have been driving for 20 years, have owned many vehicles and am not driving any differently than I have driven in the past. The dealer did not give me the vehicle as he said it is a safety issue and I was forced into changing my pads for $300. 00. Please note, I had already replaced my front brake pads and the rotors as they are worn out at only 15,961 miles in Apr-2010. But fortunately, there was a recall on the front brake and rotors , so I got this reimbursed. I filed a complaint with Chrysler and was told "too bad" and no recalls on rear brakes and rotors and they would only cover until 12,000 miles. I browsed and saw many having this same problem with brake pads and rotots. I think Chrysler has some inferior quality on these parts on these vehicles. This is very dangerous as the vehicle could catch fire and should be subjected to recall.
The contact owns a 2008 Chrysler Town & Country. The contact stated that the front driver and passenger side tire pressure valve sensors were cracked as a result of corrosion. The vehicle was taken to a dealer where the technician verified the failure and stated that it needed to be replaced. The manufacturer was not made aware of the failure. The vehicle was repaired. The failure mileage was 70,000 and the current mileage was 112,000.
The contact owns a 2008 Chrysler town and country. The contact stated that while inflating the tires, he noticed that the front passenger side valve stem was fractured. The vehicle was taken to an independent mechanic and the mechanic stated that the valve stem would have to be replaced. The vehicle was repaired. The vehicle was then taken to an authorized dealer for unrelated maintenance and the contact was informed that both passenger side valve stems were fractured. The vehicle was not repaired. The approximate failure mileage was 60,000.
Howling noises from rear wheels when moving. Touching brake pedal stops noise. Right and left calipers, rotors, and pads replaced with new. At 50,469 miles on 2/27/12, grinding noise recurred. Front wheel bearings replaced under extended warranty. At 50,484 miles on 2/28/12, noise from rear wheel recurred; left rear rotor warped, pads stuck. Replaced left rotor, freed up pads. Noise not cured. At 50560 on 3/7/12, noise verified by Chrysler mechanic, replaced right rear rotor and rear brake pads. Total cost to owner to date for these repairs: $413. 73 and many visits to dealer. Far too much wear and tear for vehicle used only for personal transportation. Took delivery October 1, 2008. Averaged 1,231 per month since purchase. All repairs completed at Chrysler dealer.
2008 Chrysler Town & Country. . . 5 recalls. . . Brakes brakes brakes. . . I have had the brakes replaced 4 times now with 96,000 miles on it. Also the rear driver side caliper froze up and I had to replace the pads,rotor,caliper @ a cost of 250. 00. The noise from the front hubs drove me crazy!! paid 550. 00 to fix them and got bad parts off the shelf. . Then I got a notice in the mail 3 months after I fixed them about bad bearings in the front and that I can be refunded the money spent to fix them. Now im trying to fill out the paper work need for the refund. .
The valve stem on tires has broken 4 times in since vehicle purchased in 2008, causing the tires to immediately and suddenly deflate. Twice when inflating tires with air, once shortly after going through a car wash and once inexplicably while the vehicle was in motion. The local Chrysler service rep at my dealer continually tells me that replacing should prevent the problem from happening again, yet it happened 4 times. Fortunately none of the incidents resulted in a crash or damage, but if the vehicle were moving at higher speeds this could be awful. I cannot believe there has been no recall on these defective parts. This is dangerous and unacceptable, and I feel my family is at risk when we are driving.