Wheel Bolts Problems of Toyota Tundra

The contact owns a 2014 Toyota Tundra. The contact stated that the vehicle was taken to ira Toyota of orleans (16 o'connor rd, orleans, MA 02653, (774) 801-7100) where it was diagnosed with needing the lug nuts to be replaced. The vehicle was not repaired. Upon investigation, the contact associated the failure with NHTSA campaign number: 17v311000 (wheels) however, the VIN was not included. The manufacturer was informed of the failure. The failure mileage was approximately 163,000.

See all problems of the 2014 Toyota Tundra 🔎.

The contact owns a 2014 Toyota Tundra. The contact stated that the lug nuts were rusted and corroded. The contact believed that the failure was directly related to NHTSA campaign number: 14v429000 (wheel). The vehicle was taken to a dealer. The technician diagnosed that it was service oxidation which was normal on the lug nuts. The manufacturer was made aware of the failure and declined to provide any assistance. The failure had not been repaired. The manufacturer was notified of the issue. The failure mileage was 800.

Wheel nuts breaking. Ref recall 08v080000. Southeast Toyota only. Mine is gulf state with same problem. Had 8 nuts fail. Toyota refuses to fix because it's not a southeast truck.

See all problems of the 2007 Toyota Tundra 🔎.

The contact owns a 2009 Toyota Tundra. While driving approximately 35 mph, the rear wheels detached from the vehicle. The vehicle was towed back to the dealer and they stated that the failure was caused by mechanical negligence. The dealer also stated that the wheels may not be secure because a special wrench was required to tighten the lug nuts. The contact called the manufacturer and is waiting for a response. The failure and current mileages were 1,100. Updated 06/09/09 the dealer stated the lugs were hard to torque. The consumer contacted the police and filed a report. Updated 06/11/09.

See all problems of the 2009 Toyota Tundra 🔎.

The contact owns a 2007 Toyota Tundra. The contact stated that the end of the lug nuts sheered off the stud that held the wheels. The dealer stated that the lug nuts were defective and replaced with different style lug nuts and wheels. There had been no further occurrences. The failure mileage was 14,600 and current mileage was 15,120.

Tundra 2002 v6 vibrated badly at 45 mph. When checking, found 3 broken studs in the front wheels, 2 from the driver side and 1 from the passenger side. With some on-line research, a TSB for this particular model and year has issued back in 2003. Yet, owners of this Tundra model had never been made aware of it. While making a call to Toyota corporation, a customer service representative stated that there is an upgrade brake system-calipers, brake pads, and other parts related to the front brake-available for free of charge for Tundras that have had brake problems. When taking this problem to a local Toyota dealer, no one seemed to take any action. 3 months later, they still didn't fix my car. Brake history-several complaints about the brakes and rotors being worn out and warped fast have been brought up the local dealer. Every time a complaint was made, the answer was that brake is not covered by the 3-year/36k warranty. When the studs broke off, dealer told me that they didn't document any of my complaints due to the facts that I never asked them to repair my brake. Wow, it sounds like they have to rip me off before they document my complaints. If others got their brake system upgraded for free of charge, then why not me?.

See all problems of the 2002 Toyota Tundra 🔎.

2003 Toyota Tundra extended cab I checked my front brake pads. When I replaced the tire, two lug bolts failed at 70ft/lbs of torque. The specifications are tighten to 80ft/lbs. When I purchased new bolts at a dealer, the parts counterman said he was selling a lot of these lately.

See all problems of the 2003 Toyota Tundra 🔎.

Consumer complaint regarding 2002 Toyota Tundra. The vehicle makes noise when turning left. The vehicle was taken to the dealer who determined that five of the lug nuts were loose due to stress. 5 of the lugs were left loose. One stud broke and one lug nut was holding the wheel in place. The consumer noticed that the tire were worn and asked the service manager to have them checked. It was determined that they were indeed worm and the tires were replaced. After the tires were replaced the consumer notice a problem with the front end that was not there prior to the tire replacement. The dealer replaced all 6 lug nuts, 1 stud and cap which was installed incorrectly. The brakes were replaced at 20000 miles and 90000 miles. About 6000 miles after the last brake service the consumer notice a pulsation when the brakes were applied. The vehicle was taken back to the dealer where they replaced the rotors.

I was rotating the tires and tightening the lug nuts when six broke. My torque wrench was set at 80 pounds, below the 82 recommendation. Two lug nuts on the right rear on one on the right front would not tighten and just kept turning. Eventually each of the lug nuts fell off, breaking the stud. The studs did not "snap" like a clean break. The lugs that broke were possibly not hardened or were made from some very soft metal. The left side produced similar results on the left rear. The left front secured all six lug nuts properly with the 80 # torque setting. On the left rear, three of the studs, all adjacent to one another broke just like the three did on the right side. I have been changing tires for 35 years and have only broken one stud previously. Eighty foot pounds of torque is not very much to break off a stud. Chevrolet currently sets lug nuts at 145 foot pounds of torque. I feel something is wrong with the lug studs on this vehicle, or at least the six that merely broke. Thirty of the lug studs held and tightened according to procedures. However, the six that broke did so before ever causing the torque wrench to reach a mere 80 foot pounds, which was actually two pounds under the recommended setting. In looking at the steel stud where it twisted apart, the metal has the appearance of cast pot metal, not cold hard steel. So far, I have received no help from the Toyota dealer. They say, "you caused them to break, it is not our fault. We change tires all day with our air impact wrenches and we are not breaking them. " a "digitorque" torque wrench is much more accurate than an impact wrench. That is why I own one because I realize the importance of setting nuts and lugs at the right setting. For these reasons, I feel that some lug nut studs that may have not been hardened, etc. , were installed on my vehicle since they broke off under very little pressure.