15 problems related to clutch have been reported for the 1999 Ford F-250. The most recently reported issues are listed below.
The caller said a piece of metal in the clutch broke and caller almost lost control. He said he had to apply the brake hard to stop the vehicle from moving forward. He was stopped at a light when the failure happened. This happened without warning. Dealer and manufacturer have not been contacted yet.
Ford f 250 safety issue, constantly have to make certain the truck doesn't lurch forward on release. The consumer is having problems with the clutch on the six speed manual and the emergency brake. The clutch releases only 1 to 1 1/2 inches off the floor. The consumer was told that the original had a rubber hose part that allowed expansion when the hydraulic clutch fluid was compressed. The vehicle was found that the problem with the clutch fork was bending. The consumer stated that it is difficult to shift gears causing a pause that could result in someone else rear ending him. The vehicle emergency brake was replaced due to recall notice however the consumer still has to leave it in gear on even theslightest grade because the emergency brake does not hold the truck in place. Ford motor company agreed to replace the parking brake front cable and the pedal control assembly. The a/c blew hot air.
Consumer states that the bushings in clutch kept breaking off. When this happened the clutch pedal went all the way to the floor, and consumer could not stop the vehicle. The piece that broke off was made of plastic, and did not do the job. This happened 3 times. The first time at 80,000 miles. Currently, it happened again and there was no recall on it.
1999 Ford F-250 superduty diesel 6 speed manual transmission. While in first gear at stop light with clutch pushed in truck started moving forward. Luckily, no one was in front of truck. The truck finally stalled. Found out later clutch master cylinder had gone bad.
F-250 super duty, 6 speed manual tran. The shifting lever attached to the throw out bearing broke. This vehicle has 45,000 miles. This was a defective part, Ford is unresponsive to my complaint. Not their problem.
Clutch slave cylinder failed without warning. The clutch pedal went about 1/2 way before engaging. Difficult to engage clutch and shift transmission. I was towing a trailer at the time of failure. When I contacted the Ford dealer to schedule repair he said not to drive the vehicle very far because complete failure would probably occur. I was also told that Ford is very aware of this defect and has redesigned this part due to many failures. Even though an accident did not occur, I think a safety recall is needed since these vehicles are designed to haul or carry heavy loads and this type of failure could make it difficult to engage the clutch when trying to stop the vehicle, which could result in a catastrophic accident. The cost for repair was $305. 26.
The tires have blown while driving on highways. The clutch problem is a recurring one. 3 to 4 times a day the clutch pedal stays at the bottom of the travel distance or only comes half-way back up. The transmission also does not shift smoothly. (tiresize: lt23585r16)( dot number: tire size: lt23585r16 ).
While making a stop by depressing the clutch, clutch did not disengage transmission, and vehicle stalled. Dealer has been contacted. Mechanic said that pilot bearing on pilot shaft is the weak link in the transmission. Pilot bearing failed, caused excessive wear on the pilot shaft which caused the clutch plate to break, which prevents the clutch from disengaging. Part replaced by dealer.
Clutch assembly failed. Nlm.
Clutch did not work in their 1999 Ford truck.
The driver applied the clutch pedal and the vehicle surged forward while having feet on the brake. Vehicle was taken to the dealer for inspection, and mechanic determined that the clutch needed to be replaced, and replaced it. However, problem recurred.
The clutch release arm failed. Scc.
Consumer states that he is having trouble with a part that attaches to the clutch release pedal, when it comes off it is impossible to release the clutch or to shift gears, the part is made of a plastic type material with teeth to keep it in place, however consumer has replaced this part several times.
When depressing clutch pedal to floor board vehicle goes into extended stoping distance. Technician stated that flywheel needed to be replaced. Please provide further information.
Clutch assembly has disintegrated twice, causing transmission and engine to lock together, resulting in loss of vehicle control.