Brake Abs Warning Light Problems of Chrysler 200

The contact owns a 2012 Chrysler 200. The contact stated that while driving at an unknown rate of speed, the traction, brake, and abs warning lights all simultaneously illuminated on the instrument panel. The contact then took the vehicle to an independent mechanic where the vehicle was diagnosed with a defective hydraulic brake module and brake pump. The mechanic called several unknown local dealers and each dealer informed him that the part was discontinued. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 149,000.

See all problems of the 2012 Chrysler 200 🔎.

My abs light has turned on. And my abs isn't working. Also my radio also is only working intermittently.

The abs and terrain lights stay on, when car reaches 60 mph it pulls.

After car in motion, it shuts off while driving, noticed that abs light came on before this happened. Sometimes after it starts, it just shuts down, car goes completely dark, I opened the door and power came back on, then I could re- start it. It is very scary because I was in major traffic when this happened.

See all problems of the 2015 Chrysler 200 🔎.

I purchased my 200 in 2017, the abs indicator light will not go off, there actually a recall but, my VIN doesn't show it. My emergency park has ignites on its while stationary at a stop sign and while in traffic at a red light, thankfully there wasn't any semi-trucks behind me because, there would have been a fatality. The car has lost power while in motion at least 3 times. Just recently my car become stuck in neutral and the car would not move. I called Chrysler, they stated that it was a powertrain issue and it would be covered with my warranty, so they paid for the tow to the dealership, the dealership had the car for a day, they counterclaimed what Chrysler stated, they claimed that it was because, the battery was just replaced so the computer needed to be re-set but, this happened on 2/12/2019 and my battery was replaced on 9/2018. There was a recall in 8/2015 for this exact same issue. I talked to the guys at my regular service station and as soon as I told them what happen they knew that I was lied to by the local Chrysler dealership.

Tl the contact owns a 2016 Chrysler 200. The contact stated that the abs indicator illuminated and went off. The failure recurred randomly. Later, the contact attempted to start the vehicle while the abs indicator was illuminated, and the vehicle did not start. The dealer and manufacturer were not made aware of the failure. The vehicle was not diagnosed or repaired. The failure mileage was 30,854.

See all problems of the 2016 Chrysler 200 🔎.

Takata recall, abs and traction light are on they make a funny noise when I first start the car and start driving. But after I go so far or to 25mph, my lights come on and I brake just fine. I also have a issue with my turn signals, if my headlights are off my front left turning sognal works but if my headlights are on my front left turning signal does not work.

Replaced disc breaks pads 3 times last year and 2 times this year, the rubber boot inside the break caliber melted and the rear breaks sometimes smokes, now front break pedal goes towards the flow and with clucking noise, andtbe abs break light is on while I was driving. .

While driving at a rate of 50 mph, the hazard lights came on without touching the control to turn it on. When I touched the control, the lights would go off for a few seconds and return flashing. This continued to occur for the next 15 miles at which time, I pulled into a parking lot. When I turned the car off. . The hazard lights came on again and could not be cut off. Other strange things that have occurred is the abs light coming on and then the car with traction streaks showing.

See all problems of the 2013 Chrysler 200 🔎.

On July 4 the abs light came on for no reason several times , staying on for long periods of time. There was a clicking noise in the steering colum and wheel . It sounded like it was coming from the left side. On July 5 , I was driving to work on a back road with several curves . The abs light came on again . Clicking was still happening as well. All of a sudden I felt like I was sliding on a sheet of ice. I swirved from side to side and could not get my car under control. Then my vehicle was on two wheels on the passenger side . Which then slide off the road and down a embankment turning several times and landing on the roof of the car. The air bags never deployed. I am now suffering with a broken collar bone due to the accident.

See all problems of the 2011 Chrysler 200 🔎.

The contact owns a 2012 Chrysler 200. The contact stated that while driving at 70 mph, the headlights failed without warning. The contact also stated that the traction control, the cruise control and the abs warning lights were illuminated. The contact also stated that there was a grinding noise coming from the front of the vehicle. The vehicle was not taken to be diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 112,000.

The abs indicator light is coming on randomly after having a front and rear brake job at the Chrysler dealership.

The contact owns a 2012 Chrysler 200. The contact stated that the abs warning light illuminated as the front end exhibited a loud metallic noise. The vehicle was taken to the dealer where a diagnostic was performed, which located the failure at the driver's side front wheel bearing. In addition, the abs system was faulty. The dealer disconnected the abs system. The driver's side front wheel bearing was not repaired. The contact also wanted to add that the water pump was replaced due to loud noises that were emitted while driving. The failure mileage was 17,000 and the approximate current mileage was 21,000.

The contact owns a 2011 Chrysler 200. The contact was driving approximately 10 mph when the check engine and abs indicators illuminated on the instrument panel. Additionally, the vehicle stalled. The failure recurred for three years. The dealer replaced two sensors, but the failure recurred. The manufacturer was notified. The approximate failure mileage was 108,000.