Chrysler 300 owners have reported 59 problems related to ignition switch (under the electrical system category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Chrysler 300 based on all problems reported for the 300.
Ignition switch.
See
all problems of the 2007 Chrysler 300
🔎.
The dealer changed the ignition switch per the recall 14v567000 for the vehicle about 2-3 years ago for a different issue with the switch. My daughter was driving the car about week ago July 30, 2020, she said she was at a traffic light on a busy street (Lincoln highway) in chicago heights IL and when it turn green she attempted to go and the vehicle cutoff and would not start back up. I arrived to her location. Another driver had pushed her into a parking lot to get her out of the middle of the highway, I tried to start the car and it would not catch. It would crank put not turn over, I had to get it towed home. After some testing of components, spark, gas pressure and fuel pump it was diagnosed with a bad ignition switch with a p2533 code that stated there was a problem with the ignition switch run position signal. This is a very troubling event since my recently turn 18 daughter has no experience with this sort of thing and thankfully there was no accident or physical harm done. I spoken with a person at a chrylser dealership service department about manufacturer coverage but she did not have a clue and transferred my call to the parts department that stated it might run $800- 1,000. 00 to replace the switch.
See
all problems of the 2008 Chrysler 300
🔎.
Ignition switch faulty, have had the ignition switch replaced twice and now need another another ignition switch dealership has claimed the ignition switch has had 4 different parts numbers so that means it has been modified 4 different times this should be a recall issue I shouldn't have to keep replacing a faulty ignition switch.
Tl- the contact owns a 2006 Chrysler 300. The contact stated that while driving at 35 mph, the vehicle stalled without warning. The vehicle was able to coast to the side of the road. The contact powered off the engine. The vehicle was able to restart after numerous attempted. The vehicle was taken to an independent mechanic where it was diagnosed that the ignition switch and key needed to be replaced. The vehicle was later taken to perry Chrysler Dodge Jeep ram dealership located at 2340 national city, CA 91950 (619) 477-1234 but was not diagnosed or repair. The manufacturer was notified of the failure and informed the contact the vehicle was not included in recall and referred the contact to NHTSA. The approximate failure mileage was 212,885. Aw.
See
all problems of the 2006 Chrysler 300
🔎.
Tl-the contact owns a 2009 Chrysler 300. The contact stated that while driving at 5 mph, without warning the vehicle stalled. The vehicle was towed to vero beach Dodge, now renamed vatland Chrysler Dodge Jeep ram located at 855 south, us-1, vero beach, FL 32962, (772) 567-6633, to be diagnosed. The contact was informed that the ignition switch needed to be replaced. The vehicle was repaired. The manufacturer was contacted and notified of the failure. The approximate failure mileage was 123,000. The VIN was not available. Ah.
See
all problems of the 2009 Chrysler 300
🔎.
The contact owns a 2007 Chrysler 300. The contact stated that he drove the vehicle home, parked it, and was unable to restart it for two days. The failure occurred without warning. The vehicle was towed to a dealer where it was diagnosed that the ignition switch was faulty and needed to be replaced. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure mileage was approximately 100,000.
Ignition switch caused engine to shut down while driving and caused problems with starting. After three trips to dealer problem was found to be the ignition switch and was replaced. Stalling while driving is a safety issue that should be cause for a recall. Note! the expensive ignition switch was replaced at my cost. I have the repair invoices.
See
all problems of the 2010 Chrysler 300
🔎.
You have sent me two recalls on airbag inflator and ignition switch. I made my first call to moore Chrysler in peoria az on 9/8/15, again 10/12/15 and today 12/8/15 and they have not received any parts to repair my car. Why is this taking so long? I believe both my recalls are serious. Please advise what I can do to get these items fixed ASAP.
This is the 4th time that my car has done this ,while I'm driving the car I just lose control of the car, I can't stop even when I hit the breaks the car want stop the car takes off while I'm behind the wheel ,the speed even goes up I have to ,shut the car off immediately from the ignition switch that starts the car,I have almost been in two bad car accidents because of this issue ,I have took the car to a local shop I was told its nothing they can do because the car is running by computer ,it is very scary I have had my kids in the car each time this has happen ,.
Tl-the contact owns a 2008 Chrysler 300. The contact stated that while at a stop light the vehicle stalled. The lights on the instrument panel illuminated. The failure recurred numerous times. The vehicle was take to a dealer where at that time the contact had a recall notice for the ignition switch. The technician replaced the ignition switch. However, the failure recurred. The manufacturer was notified of the failure. The failure mileage was 110,000. Aw.
Engine turned off while doing 60 mph. There was a recall in 2014 for this problem and fca will not perform the required repairs. This happened in 2009 at 7000 miles and it is happening again. Ignition switch will got o accessory without warning. An accident may happen with death of passengers at these speeds. Loss of control did accur.
2008 Chrysler 300. Consumer writes in regards to ignition switch and airbag recall issues. The consumer expressed concerns about the recalls being issued.
2008 Chrysler 300. Consumer writes in regards to replacement parts not available to complete ignition switch recall notice. Recall # 14v567000.
Tl- the contact owns a 2008 Chrysler 300. The contact stated that while driving at various speeds the vehicle would suddenly shut off. The vehicle was taken to the dealer who indicated that the failure was do to a faulty ignition switch. The contact was informed that parts needed to repair the vehical was not available. That the recall notice for NHTSA campaign number 14v567000 (electrical system) was received in August 2014. After contacting the dealer and the manufacturer on multiple occasions the contact was informed that the parts needed to repair the vehicle were still not available and no estimated time for receiving the parts could be given. The failure mileage was 96,000. Jft.
Tl-the contact owns a 2008 Chrysler 300. The contact stated that it took several attempts to start the vehicle and that the ignition switch was loose inside of the steering column. The failure recurred on several occasions. The vehicle was not taken to the dealer. The contact received notification of NHTSA campaign numbers: 14v567000 (electrical system) and 15v313000 (air bags), however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The manufacturer was not made aware of the failure. The approximate failure mileage was 75,000. Sw.
Tl-the contact owns a 2008 Chrysler 300. The contact stated that while stopped at a traffic light, the vehicle stalled without warning. The vehicle was restarted. The vehicle was taken to a dealer where it was diagnosed that the ignition switch needed to be replaced. The vehicle was not repaired. The contact received notification of NHTSA campaign number:14v567000 (electrical system) however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure. The failure mileage was 108,000. Ss.
2008 Chrysler 300. Consumer writes in regards to ignition switch recall parts issue. The consumer received a recall letter nine months prior and was informed the parts were not available. The consumer referenced recall # 14v567000.
The contact owns a 2008 Chrysler 300. The contact stated that the ignition switch on the vehicle seized without warning. The vehicle was included in NHTSA campaign number: 14v567000 (electrical system); however, the part to do the repair was not available. The contact also stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was unknown.
The contact owns a 2008 Chrysler 300. After parking, the vehicle failed to turn off and the ignition switch made an abnormal noise. The failure recurred several times. The manufacturer was not notified. The vehicle was not repaired. The approximate failure mileage was 68,000.
Letter from senator nelson on behalf of constituent re issues with Chrysler vehicle. 2008 Chrysler 300. The consumer stated the ignition switch in her vehicle was recalled. At any time, the vehicle could shut down and cause an accident. The consumer was informed the parts were not available to rectify the recall. In March, the tire pressure light illuminated. She was informed the tire sensor had to be ordered.
My vehicle has a delayed start/crank once key is turned, takes about three seconds to start the vehicle engine. The car has 87,000 miles on it and this just started to happen within the last few months. I initially thought it was the battery so I had firestone replace the battery. But that did not cure the problem. I than brought my vehcile to the Chrysler dealership and they did an inspection and verified that the ignition switch in fact had a delay crank concern. I also recieved a notification from Chrysler p57 recall notice. I was than informed by the dealership that there is no part available from Chrysler to fix it! I will be on some waiting list---go figure! a second wave of owners will be notified June 2015. . . . I feel sorry for them, take a number and wait. Wait and wonder if maybe while on the freeway going 65 ot 70 mph your ignition may "spring back " from run to off. . . That should be interesting when your car completely stops and you have no steering on the freeway with a mac truck behind you! seriously? I smell death lawsuit. Public safety is at risk. Chrysler does not have fix for the problem either. I bought a lemon. I want Chrysler to take there car back and give me another year model, say a 2009 that does not have this problem, or pay for a rental car during the time Chrysler decides how to remedy this problem. I feel unsafe in my car. What if one day the car doesn't even start and I am stranded at night on some road? this sucks.
There has not been an incident. About 3 months ago I was advised that the ignition switch in the Chrysler 300 would be replaced because it was defective and a safety issue. As of yet I have not been contacted that the required part was available and I was just informed by the dealer where the vehicle was purchased that it might be another month or two before the work could be performed. In the recall notice, p57 / NHTSA 14v-567, Chrysler states "they are sincerely concerned about my safety". Must not be too concerned as the defect may continue for another two months or so.
The contact owns a 2008 Chrysler 300. While driving at 25 mph, the vehicle stalled and unknown warning lights illuminated. The contact was able to restart the vehicle. The vehicle was taken to a dealer. The technician diagnosed that the ignition switch needed to be replaced. The vehicle was not repaired. The failure recurred on numerous occasions. The manufacturer was not notified of the failure. The VIN was included in NHTSA campaign number: 14v567000 (electrical system) however, the part needed to repair the vehicle was unavailable. The failure mileage was 84,000.
Tl- the contact owns a 2008 Chrysler 300. The contact stated that NHTSA campaign number: 14v567000 (electrical system) had exceeded a reasonable amount of time for repair. The dealer stated that parts were unavailable. The manufacturer was made aware of the delay. The vehicle was not repaired. The contact report notice that the key would intermittenly get stuck in the ignition switch. The failure mileage was 50,000. Az.
Have had 3 incidents in the past few months where the car would not shut off when the key was in the off position. The most recent occasion on 3/26/15 the car had been shut off and the key removed from the ignition and it continued to run with the headlights and interior lights still on. In each case, it has taken numerous tries, including putting the car in gear and moving it to be successful in shutting it down. Contacted Chrysler group and was told to take it to a dealership and have a diagnostic done, and if it was determined to be the failed ignition switch ( which I received a safety recall for in October 2014), they would cover the cost of the diagnostics. I contacted a local dealer and made appointment to have diagnostic done. Upon arrival, I informed them of what the issue was, and was told I would be waiting upwards of 3 hours to have it completed and even if they found that the issue was related to the recall, which I was told it most likely was, there was nothing they could do, as there were no replacement parts available at this time and they could not tell me an approximate date when the replacement parts would be available. I did not wait the 3 hours to have the diagnostic done. I am nervous to drive the car, as now that I am having an issue and knowing that there could be more issues related to the ignition switch recall (possible shut down while driving, etc. Etc. ). I know there are many other 2008 Chrysler 300 owners that are in the same position. This recall is taking too long to start resolving, and at least for my part in it, I have contacted a family lawyer and relayed the information, in the event that I am hurt or killed in an accident related to this safety recall. I called the vehicle safety hotline and was given the reference # 771291 for filing a complaint.
The crystler 2008 300 touring has been recalled ignition switch. Called crystler and they told me it was recalled and going to send letter. Never sent letter and when call crystler back then they said mine was made at a different place and it not recalled. Don't understand because the same ignition switch goes in every 2008 300 touring.
Received a Chrysler safety recall on defective ignition switch. Have been trying to get it fixed at my local Chrysler dealer where I purchased the vehicle. Upon each of my calls the dealer response is that they have no replacement parts and have no idea when they will have any. A safety recall with no replacement parts or any idea and a lack luster attitude as to when any will be received seems to be little regard for the public safety. My vehicle also has an airbag that was listed on the internet site for the defective airbags and when I confronted the dealer service department about three weeks ago on the matter they said there has been no recall by Chrysler to make any repairs or replacement.
Tl- the contact owns a 2008 Chrysler 300. The contact stated that while attempting to start the vehicle by turning the ignition switch the engine would sometimes delay to start. The cause of the failure was not diagnosed or repaired. The manufacturer was not notified. The contact indicated that the recall notice for NHTSA campaign number 14v567000(electrical system) was received in January 2014. After contacting the dealer the contact was informed that the parts needed to remedy the recall were not available and no estimated time to receive the parts could be given. The failure mileage was 24,000. Jft.
We were hit by a car and the car did not deploy the air bags and it cut off and all the electrical shut down and the car ignition got stuck and had to be turned over several times before it would start. I was told the problem came from the ignition switch.
My Chrysler 300 keeps loosing power. While driving on the highway at 65 mph the vehicle decides to lose its electrical power and the engine completely turned off. There was no braking power, the steering had no play but I was able to maneuver off to the left side of the road in medium traffic. I believe the keyless ignition system has a horrific defect. It is losing contact. The double sided integrated key, I believe, is losing contact with the integral ignition switch which also contributes to inconsistent starting procedure.
Tl-the contact owns a 2008 Chrysler 300. The contact stated when she inserted the vehicle key into the ignition switch and turned it the vehicle would not turn on. The vehicle was not taken to a dealer nor independent mechanic. The vehicle was not repaired. The contact received NHTSA campaign number:14v567000(electrical system) and believed the failure was related to the recall. The manufacturer was not notified of the failure. The approximate failure mileage was 133,000. Lb.
2008 Chrysler 300. Consumer writes in regards to ignition switch recall notice. The consumer was informed the parts were not available.
I switched my car off to pump gas. When I got into my car to turn in the car my key the motor wouldn't turn over. Its like my car just powered off. My key was very loose out in the ignition and it wasn't making click sounds like it normally did after you switch the key out of the lock position. My car had to be towed to the dealership and the dealership said my ignition housing was shattered. My car was working perfectly fine the entire day. Chrysler Dodge Jeep have been having recalls on the ignition switches. I think this problem should be investigated.
Tl-the contact owns a 2008 Chrysler 300. The contact stated that while trying to turn the key to the on position the ignition began to hesitate without warning. The vehicle was taken to the dealer where it was diagnosed that the ignition switch failed and needed to be replaced. The contact received notification of NHTSA campaign number: 14v567000 (electrical system). However the part to do the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not aware of the issue. The failure mileage was approximately 120,000. Ec.
Tl- the contact owns a 2008 Chrysler 300. The contact stated that the key was difficult to turn in the ignition switch in order to start the vehicle. The contact received notification of NHTSA campaign id number: 14v567000 (electrical system) however, the part was not available for the recall repair. The manufacturer was notified of the issue. The failure mileage was not available. Djr.
Problem Category | Number of Problems |
---|---|
Electrical System problems | |
Alternator/generator/regulator problems | |
Car Will Not Start problems | |
Ignition Switch problems | |
Horn Assembly problems | |
Ignition Module problems | |
Wiring problems | |
Starter problems | |
Software problems | |
Battery Dead problems |