Abs Brake Fail Problems of Nissan Murano

Tl the contact owns a 2009 Nissan Murano. While driving, the vehicle failed to stop as the brake pedal was depressed to the floorboard. The contact was able to coast to the side of the road and then continue driving. Once the vehicle was powered off and restarted, it resumed normal operation. The vehicle was taken to frank fletcher Nissan (2327 s rangeline rd, joplin, mo 64804, (417) 317-5179) where code number: c1142 was found. The dealer stated that the abs actuator failed and needed to be replaced. The vehicle was not repaired. The contact stated that the vehicle was previously repaired per NHTSA campaign number: 18v916000 (service brakes, hydraulic). The manufacturer was made aware of the failure and provided case number: 38082076. The failure mileage was approximately 128,157.

See all problems of the 2009 Nissan Murano 🔎.

Brakes failed due to abs actuator failure while in motion on a highway. Vehicle was recalled for brake fluid change and abs actuator test. Abs actuator failed 4 months after fluid change. Nissan refused to make repairs. Total cost of repair was $2400. This created an unsafe condition which Nissan refuses to acknowledge.

Tl - the contact owns a 2011 Nissan Murano. The contact stated while driving 65 mph she pressed on the brake pedal all the way to the floor in order to stop the vehicle. The vehicle was taken to dealer walser Nissan burnsville (14750 buck hill rd, burnsville, mn 55306. 612-395-4999) who diagnosed the vehicle and stated the abs actuator had failed but the vehicle was not repaired. The manufacturer was notified of the failure who opened up a case and informed to take the vehicle to a dealer. The failure mileage was approximately 115,000. Jc.

See all problems of the 2011 Nissan Murano 🔎.

Tl the contact owns a 2016 Nissan Murano. The contact stated that the vehicle failed to start and all the warning indicators illuminated. On the outside of the vehicle, there was a burning odor. The vehicle was taken to price leblanc Nissan (14295 airline hwy, gonzales, la 70737, (225) 743-8100) where it was diagnosed that the abs motor failed and needed to be replaced. The vehicle was not repaired. The VIN was included in NHTSA campaign number: 16v636000 (service brakes, hydraulic). The manufacturer informed the contact that the serial number was not included in the range of the recall and did not offer further assistance. The approximate failure mileage was 19,000.

See all problems of the 2016 Nissan Murano 🔎.

Vehicle in forward motion. . . Slow, leaving garage. Brake pedal went to floor. Did not "pump up" as with air in lines during drive through an alleyway. Dealership verified my concern and found abs actuator failed internally. Of note: the service attendant suspected what was wrong before the car was diagnosed in the shop. "have seen this before. " why was my 2009 model not included in a later recall? I believe the part failure is a serious safety concern.

Driving to work in regular commuter traffic, stop and go, approximately 15 to 20 mph. I went over a small bump in the road while I was slowing down, and immediately the brake pedal went to the floor. Stopping distance was severely impacted. I would have rear-ended the person in front of me had traffic not moved forward by that point. Brakes remain very poor, with no real brake pressure until the bottom 10% of pedal travel. Abs sensor is locked into the "release" position now, and as a result, the pedal has to travel all the way to the floor before seeing any impact to the car speed. If this had happened in a school parking lot, I would have run over a child. Please please issue a recall for this abs module that is failing on 2009 Muranos. There are so many people who are having the same problem. It is only a matter of time until someone is killed or injured. The repair costs are over $2,500 for a new part, which most people cannot afford given that the car is 8 years old and probably only worth $10,000. Mine has 60,000 miles and has always been well taken care of, so this is not an age thing - it is a 2009 model year problem. Please issue a recall ASAP. If a major accident occurs and you are aware of this problem, then you are culpable.

I have had a spongy break pedal that would go all the way to the ground when depressed and not build up pressure. Multiple inspections did not find anything wrong with the break system. The dash board lit up about a week ago showing that the abs module failed. Applying the brake feels about the same still but I lost abs, stability and traction control.

While driving my Murano and coming up to a stoplight the brakes for no apparent reason were suddenly extremely soft that I had to almost fully depress the brake pedal to the floor to get the car to stop. I was able to get the car stopped before I entered the intersection and no accident occurred. I took the car to my local auto shop and they diagnosed as the abs unit failed but I would have to go to dealer. Went to Nissan dealer who did diagnostics test which indicated a brake master cylinder failure even though I suggested it was the abs unit that had failed based on my mechanics diagnoses. Dealer replaced brake master cylinder but did not correct the brake problem. They then replaced the abs hydraulic unit which did cause problem to go away. Total repair cost was $2,479. We have a second 2009 Nissan Murano that just had the exact same thing happen to its brakes. There is clearly a failure in the abs braking system that Nissan is clearly ignoring which is clearly putting consumers at risk of injury or death. Hope the ntsb speeds up their investigation before some person or family dies due to this abs braking failure.

Tl the contact owns a 2009 Nissan Murano. The contact stated that the brake pedal had to be depressed for an extended amount of time and almost to the floorboard before the vehicle would come to a stop. The vehicle failed to stop immediately and took an extended amount of time. Hawkinson Nissan (located at 5513 miller circle drive, matteson, IL 60443, 708-252-3769) diagnosed that the abs had no failure with the hcu. The dealer flushed the brake fluid, but did not replace the hcu. The repairs were performed per NHTSA campaign number: 18v916000 (service brakes, hydraulic); however, the failure continued. The contact took the vehicle to a certified independent mechanic who informed the contact that there was a valve issue regarding the abs, which was a mechanical defect. The manufacturer was not notified. The approximate failure mileage was 123,000.

The contact owns a 2009 Nissan Murano. The contact stated that while driving at 55 mph, the brake pedal was depressed but the vehicle hesitated to decrease in speed. The vehicle was towed to a dealer where it was diagnosed that the abs control failed. The manufacture was notified of the failure. The failure mileage was 127,000.

The contact owns a 2009 Nissan Murano. While driving 40 mph, the brake pedal was depressed and traveled to the floorboard. The contact stated that the brake pedal was pumped several times and felt like a sponge. The vehicle was taken to an independent mechanic to be diagnosed. The contact was informed that the brake master cylinder failed and needed to be replaced. The brake master cylinder was replaced; however, the failure recurred. The vehicle was diagnosed a second time and the contact was informed that the abs accumulator failed and needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 61,000.

Abs module failure. Needs replacement. In case of emergency, abs,vdc and stability control are not going to control the vehicle. Also the tires lights warning and the brakes are on.